This QSC DPM-300 10 Ch. Digital Cinema Processor is a powerful solution for today’s D-Cinema audio systems. From server to speakers, the DPM offers a complete set of tools to facilitate all the signal processing, audio distribution, monitoring and automation control services required in a modern D-Cinema sound system.
The DPM builds on the legacy of QSC’s DCM and DCP products to provide all signal processing and monitoring functions for Digital Cinema in a single integrated system. Designed to be used with QSC’s Digital Cinema Amplifiers (DCA) and featuring advanced Intrinsic Correction™ settings for QSC’s Digital Cinema Speakers (DCS), the DPM optimizes loudspeaker performance while simplifying cinema sound system wiring and configuration.
The DPM 100 and DPM 100H are configurable for passive and bi-amp operation. The DPM 300 and 300H are also configurable for tri-amp and quad-amp operation. Though optimized to receive audio content directly from a D-Cinema server, the DPM is also compatible with all analog cinema processor formats and features an 8 channel analog input for integration with 35 mm audio systems. The DPM is more than an audio processor. Whether designing a system for a single auditorium or designing a large multiplex, the DPM offers the flexibility in configuration, networking, audio distribution and advanced management services to get the job done.
QSC DPM-300 10 Ch. Digital Cinema Processor Features:
- Ten digital inputs for 5.1 and 7.1 soundtracks and HI/VI
- Control and monitoring via Ethernet including full SNMP support
- Serial automation control via RS-232
- Analog Inputs for film processors, non-sync and Mic/Line
- Master volume and full 1/3 Octave Graphic EQ on all channels (except subwoofer)
- Booth Monitor loudspeaker and headphone jack
- Digital Loudspeaker Crossovers — three passive bi-, tri-, or quad-amp screen channels
- Compatible with all existing DCA amplifiers — thousands of DCA-equipped screens are ready for full network monitoring and control
- Bypass mode routes audio around failed components to insure that the show will go on
- Intrinsic Correction™ for DCS loudspeakers for optimal “out of box” performance and reduced set-up time
- Continued development of software and firmware will add new capabilities to the existing hardware with easy firmware updates
Why not buy this QSC DPM-300 10 Ch. Digital Cinema Processor from HDTV Supply today?
QSC DPM-300 10 Ch. Digital Cinema Processor Specifications:
| DPM 300 | |
| Dimensions & Accessories | |
| Dimensions (HxWxD) | 3.5"(2 RU) x 19" x 15" |
| Line voltage requirements | 100 VAC – 240 VAC, 50/60 Hz |
| Accessories included | 6 ft UL/CSA line cord, Connector Kit |
| Front Panel Controls and Indicators | |
| Monitor Volume/parameter adjust | Rotary encoder |
| LCD | 128 x 64 bit Monochrome LCD |
| Master Mute | Push buttons |
| Master Volume | Rotary encoder |
| USB Type B port | Config and management interface |
| Monitor output | 3.5 mm TRS |
| Rear Panel Connectors | |
| Network RJ45 | 10/100 Mbps network management |
| Automation Inputs | RJ45 – 6 contact closure inputs |
| RS232 | DB-9 Serial Interface |
| Channels 1-8 AES/EBU Inputs | RJ45 |
| Channels 15-16 AES/EBU Inputs | RJ45 |
| SPDIF Input | RCA — Stereo digital audio interface and Lt/ Rt Matrix |
| Analog Inputs (1-8) | DB-25 |
| Line Inputs | 3.5 mm TRS — Stereo Left and Right and Lt/ Rt Matrix |
| Mic/Line input | XLR — Mic (+ phantom pwr) or line level |
| HDMI input/output (DPM 100H) | Type A female connectors |
| DataPort connectors | HD-15 (11) — QSC amplifier interface |
| H.I./V.I. output | 5-pin Euro-style (x1) – common GND |
| Relay outputs | 3-pin Euro-style (x2) – max 30 VDC |
| Monitor Speaker | |
| Speaker | 2"x 3.5" full-range |
| Audio Performance | |
| A/D conversion | 24-bit delta-sigma, 48 kHz |
| Frequency response | 20 Hz to 20 kHz (+- .5dB) |
| Inputs/Outputs | |
| Main Analog Input | |
| Connector | DB25F - 8 channel |
| Input stage type | Active balanced input |
| Input impedance | 20k Ohms |
| Max analog input level | +14.2 dBu (4.0 Vrms) |
| Mic/Line Input (XLR) | |
| Input Stage Type | Active balanced input |
| Input Impedance | 2.2k Ohms |
| Max Analog Input Level | 26 dBu |
| Input gain | 0 to 60dB in 1 dB steps |
| Phantom power voltage | 15V |
| Stereo Line Inputs | |
| Connector | 3.5mm TRS mini jack |
| Input stage type | Unbalanced input |
| Input impedance (4dBu sens) | > 10k Ohms |
| Max analog input level (4dBu sens) | 14 dBu (4.2 Vrms) |
| Input impedance (-10dBV sens) | 2.7k Ohms |
| Max analog input level (-10dBV sens) | 0 dBV (1 Vrms) |
| DataPort Outputs (HD15) | |
| Max output level | 14 dBu |
| Dynamic range (unweighted) | > 109 dB |
| HI/VI Outputs | |
| Connector | 5-pin Euro-style with common GND |
| Output stage type | Balanced output |
| Max output level | 18 dBu (adjustable) |
| Monitor Headphone Output | |
| Connector | Front Panel 3.5mm mini jack |
| Output stage type | Unbalanced output |
| Max output level | 21 dBu |
| Dynamic range (unweighted) | > 109 dB |
| AES/EBU Digital Inputs (RJ45) | |
| Input stage type | Balanced input |
| Input sample rate | 48 kHz or 96 kHz |
| SPDIF Digital Inputs (Mono RCA) | |
| Input stage type | Unbalanced input |
| Stereo PCM or Dolby Digital Plus (DPM300H only) |
|
| Other | |
| Relay outputs (2) | 3-pin Euro-style |
| Normally open (NO), normally closed (NC), and common |
|
| Max 30 VDC @ 1A | |
| Automation inputs (RJ45 - 6 GPI) | Max input voltage 5V (3.3V typical) |
| TTL compatible dry contact closure | |
