NTI ST-IPHD-R-POELC Low-Cost HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE), Remote

NTI ST-IPHD-R-POELC Low-Cost HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE), Remote
multicasts digital video and audio signals to one or more receivers up to 393 feet away over a 1000Base-T Gigabit Network connected with CAT5e/6/7 cable.

Each Low-Cost HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx cable or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.

NTI ST-IPHD-R-POELC Low-Cost HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE), Remote Features:

Supports HDTV resolutions up to 1080p.
Ideal solution for digital signage applications.
Power over Ethernet (PoE) - power supply not required at the local or remote unit.
Broadcast real-time HDMI video and audio signals to multiple display locations with a managed or unmanaged (also known as non-managed) network switch.
Support for multiple transmitters requires a managed network switch with VLAN support. Standard LAN switches can only support one transmitter.

Each VLAN acts as a separate HDMI Over IP Channel on the network.
Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.

Transmits an HDMI signal over one CAT5e/6/7 cable.
Full Infrared Remote (IR) control of HDMI source from remote HDTV using existing source remote control.
Plug-and-Play installation allows receivers to find the transmitter automatically on the same subnet. (Network configuration may be required for managed network switch.)
Web interface for firmware updates.
Easily expandable. Add remote units as you add monitors.

Supports a maximum of 253 receivers.

Inexpensive CAT5e/6/7 cable replaces bulky video cables.
Supports 10/100/1000 Ethernet connection.
Built-in default EDID table.
HDCP compliant.
Local and remote units must be in the same LAN. The units do not support WAN connections.

Why not buy this NTI ST-IPHD-R-POELC Low-Cost HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE), Remote today?

NTI ST-IPHD-R-POELC Low-Cost HDMI Over Gigabit IP Extender with IR and Power over Ethernet (POE), Remote Specifications

Local Unit

One female HDMI-A port for source connection.
One female 1000Mbps RJ45 port for sending high definition video/audio signals and DDC signal.
One female 3.5mm port for IR transmitter (included).
- IR frequency range: 20 to 60 Khz.
Class 3 PoE compatible (10 watts maximum).
Supported input resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz.
Codec: H.264
Encoding delay: 22 mS at 30fps latency

Remote Unit

One female HDMI-A port for HDTV display.
One female 1000Mbps RJ45 port for receiving high definition video/audio signals.
One female 3.5mm port for IR receiver (included).
- IR frequency range: 20 to 60 Khz.
Class 3 PoE compatible (10 watts maximum).
Supported output resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz.
Supports embedded digital audio through HDMI compatible TVs or audio receivers.

Power

Power over Ethernet: With a switch that supports Power over Ethernet, a power supply is not required at the local or remote unit.
Local and remote unit:
- Input: 100 to 240 VAC at 50 or 60 Hz via AC adapter (not included).
- Output: 5VDC, 3.0A.
Power Consumption:
- Local: 3.5W
- Remote: 3.0W.

Max Distance

393 feet (120 meters) over Cat5e/6/7 cable.

Cables

Use HD-xx-MM cable to connect an HDMI source or display up to 50 feet away (not included).
Use DVI-HD-xx-MM cable to connect a DVI source or display (not included).
Use CAT5e/6/7 straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors (not included).

Environmental