This NTI ST-IPHD-LC Low-Cost HDMI Over Gigabit IP Network Range Extender multicasts digital video and audio signals to one or more receivers up to 330 feet away over a 1000Base-T Gigabit Network connected with CAT5e/6 cable.
Each Low-Cost HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.
NTI ST-IPHD-LC Low-Cost HDMI Over Gigabit IP Network Range Extender Features:
- Supports HDTV resolutions to 1080p.
- Ideal solution for digital signage applications.
- Broadcast real-time HDMI video and audio signals to multiple display locations with a managed or unmanaged (also known as non-managed) network switch.
- Transmits an HDMI signal over one CAT5e/6 cable.
- Plug-and-Play installation allows receivers to find the transmitters automatically on the same subnet. (Network configuration may be required for managed network switch.)
- Web interface for changing IP addresses, firmware updates and resetting units to factory default settings.
- Easily expandable. Add remote units as you add monitors.
- Inexpensive CAT5e/6 cable replaces bulky video cables.
- Supports 10/100/1000 Ethernet connection.
- Built in default EDID table.
- HDCP compliant.
- Support for multiple transmitters requires a managed network switch with VLAN/IGMP support. Standard LAN switches can only support one transmitter.
- The managed switch must support port based IEEE 802.1Q VLAN, IGMP, and permit duplicate IP addresses across the VLAN domains.
- Each VLAN acts as a separate HDMI Over IP Channel on the network.
- Number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
- Cascade managed network switches up to 3 levels, allowing the farthest display to be located up to 1,000 feet away from the source device. Each receiver can be located up to 330 feet away.
- For a point-to-many connection, a standalone network with an unmanaged network switch, hub, or router can be used instead of a managed network switch.
- It is not recommended to use any other network devices on this standalone network as it may cause a degradation in performance.
- Uses M-JPEG technology to process image compression on a fixed bandwidth.
- Note: at high resolutions, characters on PCs get noticeably fuzzy due to image compression and decompression process.
- Local and remote units must be in the same LAN. The units do not support WAN connections.
Why not buy this NTI ST-IPHD-LC Low-Cost HDMI Over Gigabit IP Network Range Extender today?
NTI ST-IPHD-LC Low-Cost HDMI Over Gigabit IP Network Range Extender Specifications:
- Local Unit
- One female HDMI-A port for source connection.
- One female 1000Mbps RJ45 port for sending high definition video/audio signals.
- Supported input resolutions: 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
- Max. bit rate: 80 Mbps.
- Codec: MJPEG
- Encoding delay: 33 mS at 30fps latency
- Remote Unit
- One female HDMI-A port for HDTV or computer display.
- One female 1000Mbps RJ45 port for receiving high definition video/audio signals.
- Supported output resolutions: 480p@60Hz, 576p@50Hz, 720p@50/60Hz, 1080p@50/60Hz
- Supports embedded digital audio through HDMI compatible TVs or audio receivers.
- Power
- Local and remote unit: 110 or 240 VAC at 50 or 60 Hz via AC adapter.
- Power Cord Plug
- ST-IPHD-LC: US NEMA 1-15P
- ST-IPHD-LCEU: Europlug CEE 7/16
- ST-IPHD-LCUK: UK BS1363
- ST-IPHD-LCAU: AS/NZS 3112
- ST-IPHD-LCUNV: US NEMA 1-15P with country-specific universal power plug adapter
- Power consumption: 3W each.
- Max Distance: 330 feet (100 meters) over CAT5e/6 cable.
- Cables
- Use HD-xx-MM cable to connect an HDMI source or display (not included).
- Use DVI-HD-xx-MM cable to connect a DVI source or display (not included).
- Use CAT5e/6 solid or stranded straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors (not included).
- Environmental
- Operating and storage temperature: 14 to 140°F (-10 to 60°C).
- Operating and storage relative humidity: 20 to 90% non-condensing RH.
- Dimensions
- WxDxH: 2.28x4.33x1.02 in (58x110x26 mm)
- Regulatory Approvals: CE, FCC, RoHS
- Warranty: Two years.
- Compatible NTI Products
- Combine NTI's video splitters and extenders for complex applications
- 4K DVI/HDMI Video Splitter (VOPEX-DVI4K-2)
- Supports HDTV resolutions to 1080p when used with the extenders.
- HDMI Quad Screen Splitter/Multiviewer
- (SPLITMUX-HD-4RT)
- DVI-D to HDMI Single Link Interface Cable
- (DVI-HD-xx-MM)
- HDMI 2.0 EDID Emulator (HD4K-EDID-EMLTR)
- Combine NTI's video splitters and extenders for complex applications
