This DVDO Xtend-USBC-USB-EUWW-1 1-Host USB-C & USB 3.2 Gen 1 100m Extender over HDBaseT is a USB extender that can transmit USB 3.2 Gen 1 signals up to 100m/328ft via a single CAT6a cable.
The EU/UK 2-Gang wall plate transmitter includes one USB-C host port as well one USB-C and two USB-A device ports. The EU/UK 2-Gang wall plate receiver includes two USB-C and two USB-A device ports.
It can be used for long distance signal transmission between USB sources such as laptops and desktop computers and USB devices such as webcams, PTZ cameras, keyboards and mice, microphones, speakerphones, printers, scanners, touch panel displays, etc…
It supports bi-directional 24V PoC (Power over Cable), allowing the power supply to be connected to either the transmitter or the receiver.
DVDO Xtend-USBC-USB-EUWW-1 1-Host USB-C & USB 3.2 Gen 1 100m Extender over HDBaseT Features:
- EU/UK 2-Gang wall plate Tx and Rx
- Extension of USB 3.2 Gen 1 up to 100m/328ft via CAT6a cable
- USB 3.2 Gen 1 connectivity with data transfer rate up to 5Gbps
- Backwards compatible with USB 2.0 and 1.1
- Hardware acceleration for isochronous and bulk transfer
- Wall plate Tx includes 1 x USB-C host port (5V@1.5A) + 1 x USB-C and 2 x USB-A device ports (5V@1.5A)
- Wall plate Rx includes 2 x USB-C (1 x 5V@1A & 1 x 5V@1.5A) and 2 x USB-A device ports (1 x 5V@1A & 1 x 5V@1.5A)
- RS-232 pass-through
- Firmware upgrade via USB-C service port
- FSYNC GPIO pass-through for industry camera use
- Bi-directional 24V PoC (Power over Cable)
- Plug-and-play with no drivers, downloads or software
Why not buy this DVDO Xtend-USBC-USB-EUWW-1 1-Host USB-C & USB 3.2 Gen 1 100m Extender over HDBaseT today?
DVDO-Xtend-USBC-USB-EUWW-1 User Manual
DVDO-Xtend-USBC-USB-EUWW-1 Datasheet
HDTV Supply partners with DVDO to sell and support all DVDO products
Why not buy this DVDO Xtend-USBC-USB-EUWW-1 1-Host USB-C & USB 3.2 Gen 1 100m Extender over HDBaseT today?
Will this extender carry USB 3.2 Gen 1 (5 Gbps) signals over long cable runs?
A: Yes — the unit extends USB 3.2 Gen 1 signals (up to 5Gbps) up to 100m/328ft over a single CAT6a cable.
Does the extender support USB 2.0 and 1.1 devices?
A: Yes — it is backwards compatible with USB 2.0 and 1.1 devices.
Can I power the system from either the transmitter or the receiver?
A: Yes — bi-directional 24V Power over Cable (PoC) lets you provide power at either the transmitter or the receiver so the other end does not need an external supply.
What USB ports and port power levels are available on the transmitter and receiver?
A: The wall-plate transmitter has one USB-C host port plus one USB-C and two USB-A device ports (device ports listed as 5V@1.5A), while the receiver provides two USB-C device ports (one 5V@1A and one 5V@1.5A) and two USB-A device ports (one 5V@1A and one 5V@1.5A).
Do I need a separate power supply for both ends if I use PoC?
A: No — with bi-directional 24V PoC you only need to supply DC 24V power to either the transmitter or the receiver; the other end does not require its own external supply.
Is the extender plug-and-play or does it require drivers?
A: It is plug-and-play and does not require drivers, downloads, or software installation for basic operation.
