HDTV Supplys WolfPack This Build Your Own 4K 30 Hz HDMI over IP Splitter is a POE HDMI video splitter over IP allowing for the distribution and switching of high definition 4K 30 Hz video signals to be sent over CAT6/7 up to 330 feet.
It uses off-the-shelf Gigabit IGMP POE switches.
This WolfPack HDMI over IP Extender uses POE Gigabit IP network technology to process and distribute 4K ultra-high-definition video signals.
How to Build Your Own WolfPack 4K 30 Hz HDMI over IP Splitter:
- Select 1 - 4K 30 Hz HDMI to LAN POE Transmitter (TX)
- Pick the number of 4K POE Receivers (RX) or TVs you have
- Pick the correct size POE Ethernet switch by adding the number of TVs you have, and add one for the TX
- It's that easy, and it is built to what you want
The WolfPack 4K 30 Hz HDMI over IP Splitter supports POE point-to-point or 1-TX to 253 RXs (TVs) over gigabit PoE switch and can also support multi-slave control of a host's networking.
What sets this 4K 30 Hz POE HDMI over IP Splitter apart from others:
- 4K 30 Hz UHD Compliancy
- POE Design - No AC Adapters Needed
- Supports HDMI In & Out
- Zero Latency
- Sends 4K 30 Hz HDMI up to 330 feet
- Field upgradable to 253 - 4K 30 Hz TVs
- No software needed, plug-n-play
- You build it for your needs
The HDMI over IP POE Splitter resolution supports 4K@30Hz 4:2:0 Ultra HD and is completely lossless, has low latency, supports full-format HDMI audio, and fully meets the audio / visual needs of high-end customers. A POE Gigabit switch is included.
Why not build your own 4K 30 Hz HDMI over IP Splitter today?
You don't have to have any IP or LAN knowledge as there are no settings you must worry about, just Plug-N-Play. This preconfigured 4K 1x2 HDMI over IP Splitter allows for the distribution of high definition 4K video and audio signals using off-the-shelf Gigabit IGMP managed switches. The 4K 30 Hz over IP Splitters use advanced technology, supporting video resolutions up to 4K Ultra HD. It can be used in Churches, Factories, Restaurants, Sport Bars and more.
HDMI over IP Splitter Transmitter & Receiver Features:
- Plug and play.
- Uses advanced POE over IP technology.
- Transmission distance is up to 100 meters or 330 feet via CAT6
- Resolution supported is up to 4K@30Hz ultra-HD.
- Supports up to 253 receivers.
- Compliant with HDMI 1.4 and HDCP 1.4 standards.
- Audio and video are transmitted digitally over a 100 Ohm CAT6 cable for lower signal loss.
- 10/100Mbps POE Ports Switch
- HDMI signal: HDMI 1.4 and HDCP 1.4 compliant
- HDMI input resolutions supported:
- 480p@60Hz
- 720p@50/60Hz
- 1080p@30/50/60Hz
- 4Kx2K @30Hz
- Audio format supported: L/R stereo audio
- TMDS signal: 0.7~1.2Vp-p
- DDC signal: 5Vp-p
- Color: Black
The 4K 30 Hz HDMI over IP Splitter uses advanced technology, supporting a video resolution up to 4Kx2K@30Hz Ultra HD. Configure any-size HDMI splitter using HDMI over IP receivers, with only the number of ports available on the Ethernet LAN switch limiting the ins & outs of your design. Multiple receivers can simultaneously connect to a transmitter to form a virtual HDMI splitter with up to 253 HDMI receivers (TVs).
Why not build your own 4K 30 Hz HDMI over IP Splitter today?
CAT6 Installation Tips (Don't Use Patch Panels)
Why not build your own 4K 30 Hz HDMI over IP Splitter today?
How is a custom WolfPack 4K 30 Hz HDMI over IP Splitter system configured?
A: Building a custom system requires selecting one 4K@30Hz HDMI-to-LAN POE Transmitter (TX), choosing the required number of 4K POE Receivers (RX) to match the total count of connected displays, and selecting a Gigabit IGMP POE Ethernet switch with enough ports to accommodate the total count of TX and RX units combined.
The system easily scales from a basic point-to-point setup up to a 1-to-253 distribution matrix based on port availability on the connected LAN switch.
What maximum transmission distances and video resolutions are supported over CAT cabling?
A: The system transmits digital video and audio signals over a single 100 Ohm CAT6 or CAT7 cable up to 330 feet (100 meters) with low signal loss.
It supports resolutions up to 4K@30Hz (4:2:0) Ultra HD alongside 1080p@30/50/60Hz, 720p@50/60Hz, and 480p@60Hz, maintaining compliance with HDMI 1.4 and HDCP 1.4 standards.
How does Power over Ethernet (POE) simplify physical installation?
A: Integrated POE technology delivers power and data over a single network cable connected to standard Gigabit IGMP POE network switches.
This eliminates the need for individual AC power adapters at each transmitter or receiver location, simplifying cable management and placement near displays and source equipment.
Are complex IP network setup or software configuration required to run this splitter?
A: No, the system operates as a zero-configuration plug-and-play unit without requiring IP or network knowledge.
There are no complex software settings or manual IP adjustments needed, allowing immediate signal distribution right out of the box using off-the-shelf Gigabit IGMP switches.
What audio formats and signal specifications does this system support?
A: The splitter supports full-format digital HDMI audio and L/R stereo audio output across connected endpoints.
Its signal specifications include a TMDS signal level of 0.7 to 1.2V p-p and a DDC signal level of 5V p-p over standard 10/100Mbps POE-capable network ports.
Where can this HDMI over IP Splitter system be deployed?
A: Because of its plug-and-play design, long-distance reach, and support for up to 253 endpoints, the splitter is well-suited for high-density AV environments such as sports bars, restaurants, churches, factories, and commercial digital signage displays.
Its modular structure allows additional receivers to be added as display needs grow over time.
