HDMI Wallplate Extender over IP with POE - You Design It


Part Number:
Contact us for availability
POE HDMI Wallplate Extender over IP
Uses H.264 LAN technology
Supports LAN Lengths to ~400 feet
Supports PC Tools Control
No AC Needed using a POE Switch
Audio Extraction at Receiver
Configure as a Network Switcher, Splitter or Matrix
Compatible with VLC Wireless
HDTV Supplys WolfPack POE HDMI Wallplate Extender over IP use our implementation of H.264 LAN technology as the compression format so it occupies a lower bandwidth and transmits HDMI video and audio over the LAN for a better picture. The HDMI Wallplate Extender over IP supports distances up to ~400 feet over single CAT6/7 cable in point to point, point to many and many to many configurations.

POE Designed: By utilizing POE (Power Over Ethernet) technology both HDMI audio and video signals and power can be sent to a device via standard CAT6/7/6a cabling. This means you do not need to install a power outlet at the device location and you can use readily available, relatively low cost Ethernet cabling with this HDMI Wallplate Extender over IP Extender.

Conversion to TCP/IP allows you to forego the limitations of point-to-point extender systems and transmit directly over your network. You can also use this HDMI Wallplate Extender over IP as a typical point-to-point extender and transmit for up to ~400 feet over a single CAT6/7 cable or 330 feet over a CAT6 cable. In a one-to-many configuration the transmitter (TX) features a static IP address and can be paired with dozens of HDMI Wallplate Extender over IP receivers on the same network.

User supplied POE Ethernet switch is required.

HDMI Wallplate Extender over IP Features:

  • Support Dynamic Host Configuration Protocol (DHCP)
  • Support one to one, one to many, many to one, many to many modes, with large cascade
  • Following the North American Wall plate standard
  • Transmit up to 120m or ~400 feet over single CAT6/7 cable
  • Using H.264 compression encoding and supports resolutions up to 1080p@60hz
  • Complies with TCP/IP protocol with a streaming bit rate to 15Mbps
  • Supports Analog 2.0 Audio Extraction at Receiver
  • Supports LPCM audio format
  • Supports PC Tools control
  • Compatible with Video Players such as VLC, etc
  • 802.3 of compliant POE (No Power Supplys needed when connecting with a POE Switch)
  • HDCP 1.3 Compliant
  • Includes a DC 5V 1A power supply when POE not used.

Don't see the size that you need? Call us right now at 833-WOLFPACK (833-965-3722) and we will give you a custom quote immediately.

Why not buy this HDMI Wallplate Extender over IP today?

HDMI Wallplate Extender over IP Specs::

  • Data compression: Comply to H.264
  • Data transmission protocol: Comply to TCP / IP
  • Supported Video format: 480i/480p/576i/576p/720p/1080i/1080p@60HZ
  • Supported Audio format LPCM, Audio sampling rate 48KHZ
  • Bandwidth required 15 Mb
  • HDCP: Compliant HDCP 1.3
  • IR: Support IR control with an IR frequency of 20 ~ 60 KHZ
  • RS232 Baud rate: Default 2400 HZ, total 8 kinds optional
  • Switch request: Supports IGMP and supports DHCP
  • Group ID Group 00 ~ group 63

Why not buy this HDMI Wallplate Extender over IP today?

Here are POE Ethernet switchers for you to review...

PoE+ # Ports Stackable Jumbo Frames Full Layer 2/3 Support PoE Watts
LUXUL AMS 2616P ✓ 24 (16 PoE) ✓ ✓ 250
LUXUL AMS 1208P ✓ 10 (8 PoE) ✓ ✓ 130
LUXUL XMS-2624P ✓ 24 ✓ ✓ 370
LUXUL AMS-4424P ✓ 24 ✓ ✓ ✓ 250
LUXUL XMS-5248P ✓ 48 ✓ ✓ 740
LUXUL XMS-7048P ✓ 48 ✓ ✓ ✓ 740
CISCO SG300 SERIES ✓ 10-52 ✓ ✓ 62-740
CISCO SG500 SERIES ✓ 28-52 ✓ ✓ ✓ 180-740
CISCO SG500X SERIES ✓ 24-48 ✓ ✓ ✓ 180-740

Q: When using point-to-point what do I need?
You either need a POE Ethernet switch (not supplied) or must use the AC adapters that come with it.