Hall Research UHBX-8X HDMI Multi-Port Sender with HDBaseT™
Hall Research UHBX-8X HDMI Multi-Port Sender with HDBaseT™ is a 1 RU box that converts 8 HDMI inputs to corresponding HDBaseT™ outputs for extension to 150 meters (500 ft) on single UTP. The extender supports HDCP, 3D, Deep Color, CEC, and 4 K (UHD) resolutions. Compatible receivers include the low-cost self-powered UH-1BT-R and UH-1BTX-R for HDMI extension to 230 ft or 330 ft respectively, or the UHBX-R-PD that supports RS-232, IR, PoH, and Long Reach modes to 500 ft. When using receivers with PoH function, a single optional 48v power supply is needed for the 8-channel sender (power supply part number: 511-PS4815).
The UHBX-8X provides both IP (Ethernet), and RS-232 ports for control. Using these ports the user can address and send RS-232 or IR commands to any of the receivers to control the remote display. IR signals can also be extended in both directions. Besides being able to create IR commands by itself (via RS-232 or IP control ports), the UHBX-8X provides a jack for an IR detector cable. The IR received by the detector can be routed to any one or combination of outputs. 8 separate IR emitter ports are also provided on the rear of the UHBX-8X which can be used if a user connects IR detectors at each remote location. This would be perfect for controlling multiple sources in a rack with the UHBX-8X.
The extender is constructed as a 1RU rack-mountable unit and has built-in power supply. LED indicators on the front panel show Link Status, HDCP status, Long Reach and Power for each of the 8 outputs. The UHBX-8X is designed and manufactured in the USA.
Hall Research UHBX-8XHDMI Multi-Port Sender with HDBaseT™ Features:
Converts 8 separate HDMI inputs to corresponding HDBaseT™ outputs
Extends IR in both directions
Can issue RS-232 or IR commands to any output (requires compatible receiver)
RS-232 and IP control ports
Supports HDCP, 3D, Deep Color, CEC, and 4 K (UHD) resolutions
Sturdy 1RU design with built in power supply
Can power compatible receivers through the cable using PoH (requires optional 48v supply)
Front panel status indicators for power, link, video and more for each channel
Designed and manufactured in the USA
Hall Research NOTE: HDTV Supply supports our Federal, State & Local Governments, Schools, Universities & Military accounts by offering an additional discount if your email address ends in .EDU & .GOV & .MIL & .ORG. Please see Options below.
Why not buy this Hall Research UHBX-8X HDMI Multi-Port Sender with HDBaseT™ today?
Hall Research UHBX-8X HDMI Multi-Port Sender with HDBaseT™ Specifications:
Video Standards: DVI (single link) and HDMI (compliant with HDMI 1.4 video specifications including 12 bit color depth, 3D video and 4K support)
Video Signal Type: TMDS
Video Connectors: Locking HDMI
DVI signal VGA (640x480) thru WUXGA (1920x1200)
HDTV signal 480i through 1080p
Digital Cinema 4K (4096x2160) - Not supported in Long Reach
Supports 4K@60 Hz (4:2:0 8 bit color) or 4K@30 Hz (4:4:4 and 8 bit color)
Audio Formats: All HDMI Embedded Audio including: LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio (32-192kHz sample rate)
DDC Compliance: Pass-Thru DDC for reading EDID directly from remotely connected LCD and HDCP handshake. DDC clock must be less than 100 KHz and the source must support clock stretching
CEC Support: Pass-Thru CEC for Consumer Electronics Control compatible devices
RS-232: Bidirectional (full-duplex) any baud rate up to 115,200
IR: Extended in both directions. Carrier modulation range from 30 KHz to 60 KHz
PoH: Power-over-HDBaseT meets IEEE 802.3af standard. The UHBX-8X supports PoH power to devices that require power up to Class 2 (6.49 watts). Requires purchase of separate supply (Model: 511-PS4815)
Power Supply: 100 VAC to 240 VAC, 50-60 Hz, 1.5A, internal;
Power consumption: 30 watts (102 BTU/hr) maximum
Storage: -40 to +158 ˚F (-40 to +70 ˚C) / 10% to 90%, non-condensing
Operating: +32 to +122 ˚F (0 to +50 ˚C) / 10% to 90%, non-condensing
Cooling: Convection, with internal temperature controlled fan
Mounting: 1RU high, standard 19" rack
Dimensions: 1.75" H x 7.75" W x 19" L (44.45mm H x 196.85mm W x 482.6mm L)
Weight: Extender 6.9 lb or 3.13 kg, Shipping 8 lb or 3.6 kg includes: Extender, power cord, and manual