Supported AV Signals |
Video |
HDMI v2.0, DisplayPort v1.2, DVI 1.0 and HDCP 2.2 |
HDCP |
Compliant with HDCP 2.2. |
Embedded Audio |
Supports pass-through of embedded HDMI audio including up to 8 channels of LPCM or HBR audio formats such as: Dolby Digital TrueHD, and DTS-HD Master Audio. |
De-Embedded Audio |
Supports independent routing of de-embedded HDMI audio: Up to 8 channels of LPCM digital audio with up to 24-bit depth and 192 kHz sampling rate. |
Downmixed Audio |
Supports independent routing of 2-channel de-embedded / down-mixed HDMI audio. |
External Audio |
Supports independent routing of analog stereo audio stream with up to 24-bit depth and a fixed 48 kHz sampling rate. |
Audio-over-IP |
Supports networked audio pass-through using 1GbE port |
Ethernet |
Built-in 1GbE Ethernet switch on all Tx and Rx units supporting 10 Mbps. up to 1 Gbps. |
USB Control |
Supports bidirectional High Speed USB 2.0 (480 Mbps.) pass-through |
IR Control |
Supports bidirectional IR pass-through |
RS-232 Control |
Supports bidirectional RS-232 pass-through UART interface with up to 115,200 baud |
Connections / Indicators |
10GbE Port (1)(2) |
1ea. shielded RJ45 connector with LED indicators, OR 1ea. Fiber Optic SFP+ slot (populated with SFP+ module sold separately) |
HDMI Input / HDMI Output |
1ea. 19-pin Female HDMI connector |
DisplayPort Input |
1ea. 20-pin Female DP connector (Input on TX) |
Analog Stereo Audio |
1ea. 3.5mm Stereo-Mini Jack (Input / Output on TX and Output on RX) |
1GbE Port |
1ea. shielded RJ45 connector with LED indicators |
USB 2.0 (2) |
TX Units: 1ea. USB 2.0 Type B connector (Configured as host by default. May be re-configured in software.) RX Units: 2ea. USB 2.0 Type A connector (Configured as destinations by default. May be re-configured in software.) |
RS-232 |
1ea. 4-pin, 3.5mm pitch, Phoenix connector |
IR Control |
1ea. IR IN: 3.5mm Stereo Mini-Jack; 1ea. IR OUT: 3.5mm Mini-Jack |
DC Power |
1ea. 5.5 mm / 2.0 mm female screw locking connector |
Diagnostic LEDs |
TX Link, RX Link, Video, USB, Power |
Hardware Reset |
1ea. Push-button to restore factory default values |
Performance |
Supported Resolutions (3) |
Up to 4K /60p with 8-bit color (4:4:4) Up to 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0) |
Maximum Pixel Clock Freq. |
Supports pixel clock rates up to 600 MHz |
Maximum Video Bit Rate |
Supports digital signal bit rates up to 6.0 Gbps./color, 18.0 Gbps. total |
Switching Layers |
Independent switching layers for all connected Video, Embedded Audio, Analog Audio, Downmixed Audio, RS-232 and IR |
Video Signal Latency (4) |
Genlock Mode: ≤ 30 µsec. (uncompressed), ≤ 120 µsec. (compressed) (4)
Genlock Scaler Mode: 3.0 msec.
Fast Switch Mode: 1-2 Frames
Video Wall Mode: 1-2 Frames
MultiViewer Mode: 1-2 Frames
|
Supported I/O Switching Array |
Size of I/O array is only limited by the size (number of ports) of the 10GbE network switch |
Recommended CAT Cable |
CAT-6A S/FTP (500 MHz) AWG 23, or CAT-7 (Europe); Compliant with TIA/EIA-568B termination standard |
Maximum Cable Distance |
up to 328 ft. (100 meters) using CAT-6A S/FTP (500 MHz) AWG 23 cable or 18 mi. (30km) using recommended Fiber Optic Media. |
HDMI Input Cable Equalization |
Supports DVIGear's SHR™ Series HDMI with cable lengths up to 15 meters at 4K /30p resolution |
Operational Modes (5) |
Matrix Switching Mode |
Fully non-blocking cross-point routing of nearly any size I/O array - only limited by size of 10GbE switch. |
Video Wall Mode |
Supports Video Wall displays using integrated scaling engine in the RX. |
MultiViewer Mode |
Supports MultiViewer displays with up to 32x sources using integrated scaling engine in the TX. |
Point-to-Point Mode |
Supports Point-to-Point Extension up to 328 ft. / 100 meters (DN-210) or 18 miles / 30 km (DN-220) using recommended cables and SFP+ modules. |
Power |
Typical Power Consumption |
DN-210-TX: 15.24 watts / DN-210-RX: 16.24 watts DN-220-TX: 9.72 watts / DN-220-RX: 11.64 watts |
External AC Power Adapter |
Input: 100-240VAC, 50-60Hz / Output: +12VDC @ 2.5A |
Mechanical |
Construction |
Heavy-duty steel enclosure with jet black finish |
Dimensions (H x W x D) |
Each Unit: 1.4" x 8.3" x 5.7" (35.0 mm x 210.0 mm x 145.4 mm) |
Weight |
Each Unit: 3.3 lbs. (1.5 kg) |
Environmental |
Operating Temp. (Environment) |
+32˚ to +104˚ F (0˚ to +40˚ C) |
Typical Case Temperature |
Tx Unit: 98.6˚ F (37˚ C) Rx Unit: 105.8˚ F (41˚ C) |
Storage Temp. (Environment) |
-4˚ to +158˚ F (-20˚ to +70˚ C) |
Operating / Storage Humidity |
10% to 90% (non-condensing) |
Regulatory Approvals |
TX / RX Units |
FCC, CE, RoHS |
External AC Power Adapter |
FCC, CE, UL, C-UL, CEC, GS, PSE, CCC, RoHS, WEEE |
Warranty |
Limited Warranty |
3 Years Parts and Labor |
Model Numbers |
DN-210-TX / DN-210-RX |
DisplayNet HDMI 10GbE Transmitter / DisplayNet HDMI 10GbE Receiver |
DN-210U-TX / DN-210U-RX |
DisplayNet USB 10GbE Transmitter / DisplayNet USB 10GbE Receiver |
DN-220-TX / DN-220-RX |
DisplayNet Optical 10GbE Transmitter / DisplayNet Optical 10GbE Receiver |
DN-220U-TX / DN-220U-RX |
DisplayNet USB Optical 10GbE Transmitter / DisplayNet USB Optical 10GbE Receiver |
DNS-200 |
DisplayNet Server™: Rack-mountable Windows 10 PC with DisplayNet API and DisplayNet Manager™ Software pre-installed. |
Accessories |
Included |
1x External AC Power Adapter (per unit)
2x Mounting Brackets with Screws (per unit)
1x HDMI Gold-Plated Jack Screw (per unit)
1x 4-pin RS-232 Phoenix Connector (per unit)
1x IR Transmitter (per TX unit)
1x IR Receiver (per RX unit)
1x USB Flash Drive Loaded with: Hardware Manual, Software Manual
|
Optional |
DisplayNet Server™ (model DNS-200) (6)
External AC Power Adapter with USA, Euro, UK, or Australia Plugs
Power Distribution Unit, 8x 12VDC (DVI-7520-PDU)
IR Transmitter (DVI-7360-IR-TX), IR Receiver (DVI-7360-IR-RX)
19" Rack Mount Kit (DN-100-RMK)
DVI-I Female to HDMI Male Adapter Cable (DVI-8511b)
|