HDTV Supplys WolfPack 1x4 HDMI Distribution Amplifier is an HDMI splitter with four RJ45 outputs. Our 1x4 HDMI Distribution Amplifier distributes the input of the HDMI signal into the four identical outputs simultaneously. Four HDMI Extender Receivers by CAT5 receive the HDMI distributed signal from the splitter and transmit to displays individually. Each receiver works with the DA as a full functional module. Only by the most inexpensive UTP cable with cross stand inside the full functional module extend the HDTV display up to ~300 feet 50 meters for 1080p. The 1x4 HDMI Distribution Amplifier extend HDMI signals out to 4 ports approximately to 300 feet displays and it also supports one to many and cascade extension.Simply locate the 1x4 HDMI Distribution Amplifier at the high definition source, locate each of the four receivers at the monitors. Now each the monitors may be connected using a single run of Cat5e or Cat6 cable, each with a maximum length of 160′. No more HDMI cable length limitations, no more pulling delicate, bulky pre-terminated cable, hoping it is not damaged in the process.
Our 1x4 HDMI Distribution Amplifier sends one HDMI source to 4-widescreens over a single CAT5e/6 cable to each widescreen or projector. Those CAT5e/6 cables can be up to 300 feet long
1x4 HDMI Distribution Amplifier Features:
- Supported Video Resolutions:
- 640X480 @ 60fps
- 800X600 @ 60fps
- 1024X600 @ 60fps
- 1024X768 @ 60fps
- 1152X864 @ 60fps
- 1280X600 @ 60fps
- 1280X720@ 60fps
- 1280X768@ 60fps
- 1280X800@ 60fps
- 1280X960@ 60fps
- 1280X1024@ 60fps
- 1440X1050@ 60fps
- 1440x900 @ 60fps
- 1600x900 @ 60fps
- 1660x1200 @ 60fps
- 1680x1050 @ 60fps
- 1920x1080 @ 60fps
- 1920 x1200 @ 60fps
- Supports HDMI 1.3/HDCP1.1 & 1.2
- Supports point-to-point, point-to-multi point transmission and cascaded
- Follows all international standards
- Supports interlaced and progressive display mode
- Supports IR extension so you can control the set-top box or Blu-ray receiving site with an infrared remote control
- Pure hardware design, plug and play so no need to install additional software
Why not buy this 1x4 HDMI Distribution Amplifier today?
1x4 HDMI Distribution Amplifier Features:
- Video Resolution Supported:
- 640X480 @ 60fps
- 800X600 @ 60fps
- 1024X600 @ 60fps
- 1024X768 @ 60fps
- 1152X864 @ 60fps
- 1280X600 @ 60fps
- 1280X720@ 60fps
- 1280X768@ 60fps
- 1280X800@ 60fps
- 1280X960@ 60fps
- 1280X1024@ 60fps
- 1440X1050@ 60fps
- 1440x900 @ 60fps
- 1600x900 @ 60fps
- 1660x1200 @ 60fps
- 1680x1050 @ 60fps
- 1920x1080 @ 60fps
- 1920 x1200 @ 60fps
- Sound: Sampling Rate：32kHz, 44.1kHz and 48kHz
- IR Support: 38KHz; NEC code
- HDMI version: HDMI 1.3
- HDCP Version: HDCP 1.2
- Power Input: DC input: 5V/2A
- Transmitter: 10W Maximum power consumption:
- Receiver: 10W Maximum power consumption:
- Dimensions (length - width - height) 167mm*80mm*28mm
- Weight: 770g
- Operating temperature / humidity: 0℃ - 70℃ / 10% - 80%RH(Not frozen)
- Storage temperature / humidity: -10℃ - 80℃/ 5% -90% RH(Not frozen)
